Quick Start Guide Bluetooth Inductor Necklace with Spy Earpiece
Easy to Use
- Put the battery in the earpiece and then insert it into your ear,
- Turn on the Bluetooth system,
- Activate the Bluetooth connection from the phone (compatible with any phone),
- Search for new devices and connect the Bluetooth to your phone
- Put the inductor necklace around your neck,
- Call the person you want to speack
- You can call the last number in the list by pressing on the Bluetooth at the base of your neck without having to use your mobile phone,
- put the phone on silent and hide it somewhere with you,
- a little below the base of the neck you have a very high-performing microphone.
What can you do if
If the sound from cheating spy earpiece have poor quality or has low intensity
Gsm box and bluetooth device use same spy earpiece so advices from next video may helpyou to solve this situation. If when you test mini bluetooth device with mini invisible spy earpiece, inside your ear sound(voice of your helper) have low intensity or quality is poor (with many distorsions) ceck this video to see advice what can you doo in this situation for fix the problem.
If sound is lower:
- hold the bluetooth device more closer to your cheating earpiece
- change the battery in the cheating earpiece
- press many thimes + (Up Volume) from your phoen what is connected to the bluetooth to encrese volume level
If the sound have bad quality:
- not set volume to the maximum level!!
If it is heard slowly and after you have checked the steps above, most likely yellow wax got into the spy cheating earpiece and either the earpiece got clogged or the wax (usually the liquid one) got to the speaker membrane and, having a high viscosity, stuck it moving harder. The cheating earpiece must be replaced with a new oane. Clean very stryctly before insert earpiece inside ear, damage earpiece with wax is not cover by warranty.
If the sound from cheating spy earpiece have poor quality or has low intensity
Gsm box and bluetooth device use same spy earpiece so advices from next video may helpyou to solve this situation. If when you test bluetooth device with mini invisible spy earpiece, sound have to high intensity – is heard outside of your ear, check next video to see what can you do for fix this problem.
The further you hold the bluetooth device from the earpiece (ear), the slower you will hear. Put the bluetooth device as close as possible to the ear(cheating earpiece) and never below the chest, because the bluetooth device has a microphone and the closer it is to the mouth the person you are communicating(your helper) with will hear and understand you much more easily.
If there is noise in the exam room where you want to use the device, first of all, it will be louder because the bluetooth device is close to the headphones in the ear, and secondly, you can adjust how loud it can be heard by bending your head towards the box (it will be heard from the louder the closer you get to the bluetooth device with the ear in which you have the headset) or move your head away from the bluetooth device for cases when someone is next to you and you want to be sure that they will not be heard outside.
Make several tests by adjusting the volume from “+” for louder and “-” for slower, and have someone sit next to you and check if it can be heard outside, changing at the same time the place and position of the bluetooth on the body.
In order not to be heard outside, you must find a balance between the position of the bluetooth cheating device on your body – the volume set by you at the phone – and the position of your head in relation to the bluetooth device as I described above.
The fact that you need to adjust the volume without having to have access to the device during the exam by tilting your head, respectively approaching the ear where the bluetooth device is located for a louder in-ear volume and removing the ear from the bluetooth device for a lower volume represents. A very big advantage because in different situations it is of a larger volume and in other situations a small volume.
Step 1: Clean the ear very well before putting the earpiece on the ear
Due to the technology used, the very small size, the earpiece is very sensitive and therefore try not to lose it on foot, not to keep it close to large magnetic or electromagnetic fields, and very important not to infuse it with wax!
You need to clean your ear very well before inserting the earpiece – you will infuse it with yellow wax and it will be heard very slowly and over time the wax will destroy the internal circuits.
Step 2: Insert the 337 Battery in the Wireless Earpiece
The battery has 2 sides: a side is completely smooth and has something written on it and the other has a circle on the edge. Every time the battery will be put in the cover with the part with the writing facing the cover and the circle around the edge towards the wireless earpiece:
DO NOT pull off the cover – the cover is opened by spinning! Screw with care the wireless earpiece cover. If immediately you start screwing it, it gets stuck, open and screw on again. Screwing has to be done very easily, there is no need to force it. When you put the battery in your headset after fixing the cover it is possible to leave a little space between the headset and the cover (the cover is not tighten all the way) – this is normal!
The wireless earpiece battery will start to be consumed from the moment you screw the cover, even if you do not use the wireless earpiece, therefore it is recommended not to leave the battery in. The battery’s autonomy is of about 3-4 hours of operation.
The battery can be used several times, provided it is not left in the wireless earpiece. The wireless earpiece will be inserted into your ear all the time with the sharp side facing your ear. It will be pushed with a tweezer until it is no longer visible. When you remove it, you will draw it with a small tweezer from that little transparent antenna.
That antenna on the headset has absolutely no role in operating the wireless earpiece and is placed just for removing the headset from the ear. Some customers shorten or even cut it off in order to be harder for the headset ro be seen in their ear, but be careful: you will not have anything in order to help you take off the headset out of your ear and thus it will be very difficult to remove it.
The headset has a background noise (like a continuous fizzle, rustling) – this is normal, that means the amplification of the wireless earpiece works and the headset is new. The more intense the background fizzle is, the more intense the voice of the person who dictates you will be. In the meantime, the intensity will drop along with the wireless earpiece wear until nothing will be heard- this means you have to replace the headset.
Step 3: Put the necklace inductor around your neck
The necklace must necessarily be placed around the neck like a chain. In no way do you put the necklace elsewhere, do not tighten the pile and put it below, under the arm, in your pocket, etc. To better mask (hide) the necklace around the neck we recommend that you attach it to the body with leucoplast or medicinal patches, NOT with shells because you will sweat and it will come off!
The necklace is quite wide and you will position it beyond the contour of the neck. We recommend the use of a dark color blouse (black is perfect) and as thin as possible so as not to reduce the sensitivity of the microphone, without too generous cut to the ladies and ladies.
In no way do you cut that necklace! In exceptional cases you can put it in 2 and possibly put it inside the necklace from a shirt taking care that under the ear you put the microphone to be several inches of necklace, but the intensity of the sound in the earpiece will decrease considerably.
What you not to do, WARNING!!!
You need to clean your ear very well before inserting the wireless earpiece: you will clog it with wax and it will sound very slowly and in time the wax will destroy the internal circuits.
- Do not pull on the cover from earpiece – the cover opens by turning(screw),
- Do not use batteries other than 337,
- Do not put the battery backwords in the cover – you will burn the earpiece
- Because of the technology used, the very small size, the earpiece is very sensitive, so try not to drop it, not to keep it close to magnetic or electromagnetic fields, and it is very important not to clog it with wax.
- Do not worry about that background fizzle, it’s normal, it means the earpiece works, when it goes away, the earpiece has deteriorated and needs to be changed
- Do not place the necklace anywhere other than around the neck
- DO NOT cut the necklace to put it in the necklace !!!